Polycarbonate belongs to the engineering thermoplastics, and its backbone carries the repeating -[O-R-O-CO]- linkage that defines the family. Ester groups in the molecular structure split the material into aliphatic, alicyclic, and aliphatic-aromatic types. Only the aromatic version has real commercial value. Within that group, bisphenol A polycarbonate does most of the work, with molecular weights running from 30,000 to 100,000.
Structurally, PC is amorphous. It is odorless, non-toxic, and highly transparent, ranging from colorless to a faint yellow tint. The mechanical profile is what sells it: impact resistance first, then high tensile strength, bending strength, and compressive strength. Add good toughness, heat and weather resistance, easy coloring, and low water absorption, and you have a resin that suits a wide spread of parts.
Heat performance is solid. Deflection temperature under load lands between 135 and 143°C, creep stays low, and dimensions hold. Over a broad temperature range the material keeps its mechanical properties, dimensional stability, electrical behavior, and flame retardancy. Continuous service runs from -60 to 120°C. There is no sharp melting point; PC sits in a molten state around 220 to 230°C. The molecular chain is rigid, which is why the melt comes out thick and viscous.
Shrinkage is low, generally 0.1% to 0.2% by the resin figures, which supports tight dimensional accuracy and stable parts. Film made from PC also shows low permeability. The material is self-extinguishing, stable under light, though not resistant to ultraviolet, and it holds up well outdoors. It resists oils, acids, strong alkalis, oxidizing acids, amines, and ketones. Chlorinated hydrocarbons and aromatic solvents will dissolve it. PC also brings antibacterial, flame retardant, and anti-pollution behavior to the table.
Two chemical weaknesses matter. Prolonged contact with water invites hydrolysis and cracking. And the same solvent resistance that helps in some applications turns into a liability elsewhere, because the resin cracks under stress when fatigue resistance and solvent exposure combine. Poor flow and poor wear resistance round out the short list of drawbacks.
Processing routes are broad. PC can be injection molded, extruded, compression molded, blow molded, thermoformed, printed, bonded, coated, and machined. Injection molding carries the most volume by far.
Temperature drives everything with this resin. Melt viscosity drops sharply as temperature climbs, and flow accelerates with it. Pressure does little by comparison. If a part needs better flow, the answer is more heat, not more force. Drying comes before anything else. Roughly 120°C for three to four hours, with moisture held under 0.02%. Even trace moisture will produce hazy color, silver streaks, and bubbles once the melt hits processing temperature.
Room-temperature behavior opens up another set of options. PC accepts considerable forced high elastic deformation without failure, and its impact toughness is high enough that cold pressing, cold drawing, and cold rolling all work.

Molding runs hot and slow. High melt temperature, high mold temperature, high pressure, low speed. Small gates call for low-speed injection; other gate types take high-speed injection. Mold temperature should sit around 80 to 110°C, with the melt at 280 to 320°C. Shrinkage in molding is commonly quoted at 0.5%, so size change across the cycle stays small.
The defects to watch for are predictable. Gas bubbles on the surface, gas lines at the nozzle, heavy residual stress inside the part, and cracking. Annealing after molding relieves that internal stress and is standard practice on demanding parts.
Extrusion has its own rules. Use a resin with molecular weight above 30,000, run a gradual compression screw with a length-to-diameter ratio of 1:18 to 1:24, and set compression ratio at 1:2.5. For clear bottles at high quality, extrusion blow molding, injection-blow molding, and injection-stretch-blow molding all apply.
Where the material ends up is telling. Three sectors dominate: glass assembly, automotive, and electronics and electrical. Behind them come industrial machinery parts, optical disks, apparel, computers and office equipment, medical and health care products, films, and leisure and protective gear.


