ABS Plastic Properties, Processing and Applications: A Practical Guide for Engineers

Nov 05, 2026 Leave a message

ABS earns its place on so many bills of materials because of how it is built. The polymer is a ternary copolymer synthesized from three chemical monomers: acrylonitrile, butadiene and styrene. Each one brings something different to the table. Acrylonitrile contributes high strength, thermal stability and chemical stability. Butadiene supplies toughness and impact resistance. Styrene makes the material easy to process while delivering a high finish and high strength.

The polymerization of these three monomers produces a two-phase structure. The continuous phase is styrene-acrylonitrile, and the dispersed phase is polybutadiene rubber. Morphologically, ABS is a non-crystalline, amorphous material with high mechanical strength, often described as combining toughness, rigidity and steel-like performance. It falls into the category of general-purpose engineering plastic, which is why people simply call it general-purpose plastic. One variant worth knowing: MBS is referred to as transparent ABS.

From a physical standpoint, ABS appears as a light yellow granular or beaded opaque resin. It is non-toxic and odorless, with low water absorption and good overall physical and mechanical properties. Its specific gravity sits at 1.05 g/cm3, slightly heavier than water. Shrinkage is low at 0.60%, which translates into stable dimensions and easy molding and processing.

What makes ABS especially flexible for designers is that its characteristics depend heavily on the ratio of the three monomers and the molecular structure within the two phases. Adjust those variables and you get a different material. That is why hundreds of different grades of ABS are available on the market today. Depending on the grade, buyers can find medium to high impact resistance, low to high finish, and varying high temperature distortion properties. ABS also offers superb processability, excellent dimensional stability, low creep and high impact strength. Mechanically it performs well electrically, resists wear, holds its dimensions, withstands chemical attack and takes surface gloss nicely.

Its weaknesses are just as real. Weather resistance and heat resistance are poor, and the material is flammable.

ABS plastic pellets and injection molded parts illustrating material properties and processing

Processing ABS well starts before the machine even runs. The resin is highly hygroscopic and moisture sensitive, so it must be fully dried and preheated before molding. The standard practice is drying at 80 to 90°C for at least 2 hours, bringing the moisture content below 0.03%. Skip this step and the finished parts will show the consequences.

Temperature control during injection behaves differently than with other amorphous resins. ABS melt viscosity is less sensitive to temperature. Its injection temperature runs slightly higher than that of PS, but unlike PS, it does not offer a wide temperature rise range. Raising the temperature blindly will not reduce viscosity. The better route is increasing screw speed or injection pressure to improve fluidity. The general processing temperature window is 190 to 235°C.

Pressure matters too. ABS melt viscosity is medium, higher than that of PS, HIPS and AS, so plasticizing calls for a higher injection pressure of 500 to 1000 bar. Medium to high injection speeds give the best plasticizing effect. There is an exception: complex shapes and thin-walled parts sometimes require higher injection speed, though the gate area is prone to gas marks under those conditions.

Mold temperature is generally adjusted between 25 and 70°C. For larger products, the fixed mold, meaning the front mold, runs about 5°C hotter than the movable rear mold. Keep in mind that mold temperature affects the finish of plastic parts, and a lower temperature leads to lower finish.

One more caution: ABS should not stay in the high-temperature barrel for long. Anything beyond 30 minutes invites decomposition and yellowing.

The application list reads like a cross-section of everyday manufacturing. Automotive uses include instrument panels, tool hatches, wheel covers and mirror boxes. Refrigerators rely on it, and so do high-strength tools such as hair dryers, blenders, food processors and lawn mowers. Telephone housings and typewriter keyboards are classic ABS parts, and the material shows up in recreational vehicles like golf carts and jet snowmobiles.

If you are evaluating ABS for a new part, it helps to work with a manufacturer that runs this process daily. TCHD offers plastic injection molding capabilities, and you can send your drawing and production requirements for a technical review.